Updated 17 November 2026
How do you brief a standing pouch that contains an instruction card?
Provide the card dimensions, the thickness of the product in its packed state, and the order in which you plan to insert them. Ask for a pouch sample to see whether the card can pass through the opening without folding and stay below the closure area. After closing and reopening the pouch, check that customers can remove the card as intended. Record where the card sits, the space left, and any changes needed to the sample pack.

Start with the printed card and the actual product
Measure the length, width, and thickness of the card as it will be used. If it is folded, measure it folded and mark the spine. Photograph its edges if it has stiff corners, thicker laminate, or a projecting tab. Measure the thickest point of the product in its intended arrangement, including any inner wrapper. If there are several variants, mark the combination that takes up the most room. A temporary paper card can help you assess positioning, but check again with the final printed material before approving the pouch.
Distinguish outside dimensions from usable opening width
The outside pouch width can include side seams. The opening at the closure can be narrower than the body. Ask the packaging team to show where to measure the opening on the sample or drawing. Try passing the card through with and without the product inside, in an orientation staff can use comfortably. If operators have to fold the card or pull hard against the pouch sides, record where they encounter resistance. Try changing the insertion angle or card dimensions before specifying a different pouch size.
Compare two packing sequences
For the first sample, insert the card first and hold it flat against the pouch wall as you add the product. Check whether the product pushes the card into a fold or presses it against the side seam. For the second sample, load the product first and slide the card into its final position. See whether the filled pouch leaves a clear path for the card. If the results vary from one trial to the next, note where the card catches. Choose a sequence that staff can repeat with similar samples using their available packing setup.

Keep the card clear of the closure
Close the sample pouch using the method planned for the finished pack. Check that the top of the card stays inside the pouch body, especially if movement of the product can push the card up. Keep the intended card position away from the zipper track or seal area shown in the design. Ask the supplier what space its closure needs. If the process includes a separate sealing step, follow the equipment procedure and check the position on a sample before operating. Record whether the card moves when the pouch stands up or lies flat.
Check how the customer retrieves the card
Open a pouch the way a customer would on first use. Ask someone who did not watch the packing trial to find and remove the card without extra instructions. Check whether the card is visible, whether its edge is within reach, and whether the product blocks the path out. If customers need the card before using the product, place it where they can see it without moving much of the contents. If the card sinks to the bottom or is awkward to remove, record the result and try another position in the next sample. Check that the printed portion comes out intact.
Test variants that change the pouch shape
Inspect the pouch upright because the contents can move as the base opens out. Test the thickest product variant and the stiffest card. Record whether any bulge affects one side or also pulls at the top of the pouch. If a card corner rests against the wall, try rotating the card or discuss changing its shape with the design team. Keep front and side photos for each variant. If the product’s characteristics or hygiene requirements call for separation from the card, discuss a suitable inner wrapper with the supplier before approving the design.
Include trial evidence in the request for quotation
Combine a photo of the card, the sample opening dimension, product code, card position, and opening-trial results. Include the closure you are considering, approximate pouch quantity, printing requirements, and destination city. If you used a temporary card, describe differences planned for the final dimensions or material. Ask the supplier to confirm the dimensions in use and whether it can provide a sample with the same closure. Tie the quote approval to the drawing revision or sample code so purchasing can recheck the dimensions if the design or order contents change.
Keep a reference for packing staff
After choosing the sample, take photos of card insertion and final product position. Show which way the card faces and where its edge should stop relative to the closure. Include one example of a condition to correct, such as a trapped card corner. Keep the sample code so changes can be tracked. When a revised instruction card arrives, compare its dimensions and stiffness and repeat the trial with the real product. Record the result in the work instructions and the purchasing record for that pouch before rolling the printed change out across production.
An example of a card that nearly fills the opening
If the card is nearly as wide as the usable opening, check that packing staff can grip it without making insertion difficult. Repeat the trial with several pouches of the same design. Mark the photo if the corner commonly catches at a side seam or behind the zipper. If insertion only becomes easy when the pouch lies flat, note how that affects the product position. Consider a narrower card only if its essential information remains legible. After changing the size, repeat the opening trial and see whether the card is still easy to find.
Check the difference between inserting and retrieving the card
During filling, staff may use both hands or the usual equipment to hold the pouch open. A customer may open it while holding another item. A smooth insertion therefore needs to be checked against retrieval after the pouch has been closed. Record whether the customer must empty the pouch to see the card. If they need the instructions before using the product, try a position where the upper edge is visible as soon as they open it. The final position still needs to sit below the closure and be possible to inspect before the order moves on.
Identify choices that are still open
If the supplier receives a table with two card sizes still under consideration, mark both as options to test. Keep the small card trial separate from photos of the larger card. Link each option to its design code, trial result, and product variant. Once you decide, add the date and responsible person’s name to the summary so purchasing can identify the approved revision. If the final dimensions only become available after a print sample, repeat the trial before approving a larger pouch order.
See the Cave Mekar Group standing pouch product page and use its quote form link to discuss the dimensions and results of your packing trial.
Frequently asked questions
Is the outside pouch width enough to assess the card?
Measure the usable opening and try passing the card through a sample with the actual contents.
Which component should go in first?
Try both sequences with the same product. Choose the sequence that keeps the card flat and accessible.
Can the card sit close to the zipper?
Position the card below the closure track and check that handling does not shift it into the track.
Can I use a paper card in the first trial?
Yes, to check the initial position. Repeat the trial with the finished card to assess its actual thickness and stiffness.
What should I send with the trial photo?
Include card dimensions, measured opening, sample code, packing sequence, and the results of the opening trial.

